Whoop F4 AIO 12A&20A brushless V3 flight control ESC integrated module through drone | Parts & Accs

Whoop F4 AIO 12A&20A brushless V3 flight control ESC integrated module through drone | Parts & Accs

Unavailable in 

F405 2-4S AIO 12A brushless flight controller (BLHeli_S) V3 has updated the F411 chip to F405, which can fully handle 12A continuous current (13A burst), providing powerful flight power for flight. It is strongly recommended to use it on Beta75X series drones, Beta85X series drones and HX100 series drones.

The 20A F405 AIO FC reduces the thickness of the board from 1.6mm to 1.2mm, thereby reducing the weight to 5.3g, while improving the ability of the ESC to continuously current 20A (22A burst). Now you can use the powerful FC to build larger quads to reduce weight and size.

Since the 12A V3 flight controller and the 20A AIO V3 flight controller unify the UART, the two boards have the same appearance/flight control schematic diagram/LED indicator and the way of connecting the receiver.

Product Description:

Update the F411 chip to F405, the 12A/20A board can handle 12A/20A continuous current (13A/22A burst), which provides a powerful flight experience for flying.

With 2 integrated plug-and-play ports for digital image transmission and receiver, it requires less welding work and is easy to install.

The traditional mounting hole is completed, which is more like a "toothpick" type, which can perfectly prevent the damping pad from falling, which is very easy to install in most whoop racks.

BETAFPV 12A/20A AIO flight control unites UART, which is convenient for welding.

Compatible with 110X, 120X, and 140X motors, you can use 20A (12A) AIO flight control to build a larger machine, thereby reducing weight and size.

Compared with the F4 12A AIO flight control V2 version, the difference between the F405 12A AIO flight control V3 version and the F405 20A AIO flight control V3 version is shown in the figure below.

Product parameters:

F405 20A AIO FC V3

CPU: STM32F405RGT6

Six axis: MPU6000

Size: 26mm x 26mm

Firmware version: Batefight-BETAFPV405-4.2.X

OSD: Built-in BetaFlight OSD (STM32 controls the OSD chip through SPI in DMA mode)

Receiver: Support Frsky XM/ XM+/Futaba/ Flysky/ TBS Crossfire/ DSMX

Connector: XT30

Weight: 5.3 grams

ESC specifications

Support PWM, Oneshot125, Oneshot42, Multishot, Dshot150, Dshot300, Dshot600

Input voltage: 2S-4S Lipo

Continuous current: 20A

Peak current: 22A

Firmware: BLHELI-S GH-25

F405 12A AIO FC V3

CPU: STM32F405RGT6

Six axis: MPU6000

Size: 26mm x 26mm

Firmware version: Batefight-BETAFPV405-4.2.X

OSD: Built-in BetaFlight OSD (STM32 controls the OSD chip through SPI in DMA mode)

Receiver: Support Frsky XM/ XM+/Futaba/ Flysky/ TBS Crossfire/ DSMX

Weight: 5.3 grams

Connector: XT30

ESC specifications

Support PWM, Oneshot125, Oneshot42, Multishot, Dshot150, Dshot300, Dshot600

Input voltage: 2S-4S Lipo

Continuous current: 12A

Peak current: 13A

Firmware: BLHELI-S GH-25

F405 20A AIO flight control V3 and F405 12A AIO flight control V3 line drawing:

There are two LED indicators at the bottom of the flight control, including the power indicator (red) and the flight control indicator (blue). For the status, please refer to the following pictures.

The connection guide diagram of the external receiver: How to connect the external receiver to F405 20A AIO flight control V3 and F405 12A AIO flight control V3

This flight controller reserves a plug-and-play port for the external receiver to reduce soldering (a 4-pin terminal cable is included in the package). Please note that when connecting different external receivers, the pads near the pins need to be pre-soldered as shown below:

pack

1 * F405 20A AIO FC V3 or F405 12A AIO FC V3

4 * M1.2x4mm screws

4 * M1.4x5mm screws

4 * Shockproof rubber shock absorber

1 * 6-pin digital image transmission cable

1 * 4-pin receiver cable